designed & dimensioned in millimeters do not scale from this print mps-xx-x.xx-xx-x-v-xx no of positions -02, -04, -06, -08 vertical lead style -01: for 1.57[.062] thick pcb (use sub-c-214-xx.xx-01-x) -02: for 3.18[.125] thick pcb (use sub-c-214-xx.xx-02-x) 03: for 2.36 [.093] thick pcb (use sub -c-214-xx.xx-03-x) plating specification -l: see table 2 -t: see table 2 option -lc: locking clip (use lc-07-tm) (see fig. 2, sht 2) -7.70 -9.70 (see table 1) tail length * * = not tooled ** = not released for production * ** -hs: hot swap (see fig. 3, sht 2) (no of pos x 5.00[.197]) + 7.55[.297] ref 10.16 .400 ref 5.00 ref (typ) .197 (no of pos-1) x 5.00[.197] "a" "a" c c l 01 j 1.88 (typ) .074 (no of pos x 5.00[.197]) - 3.12[.123] 2.50 .098 ref "b" ref 0.38 .015 ref 1.00 ref .039 (no of pos x 5.00[.197]) + 2.64[.104] ref 1.27 .050 ref 1.47 - 0.13 +0.05 .058 - .005 +.002 0.41 ref (typ) .016 "b" "b" section "a"-"a" c c c c l check bow on this surface (see note 5) 2.54 .100 2.54 ref (typ) .100 "a" - 0.50 +0.25 0.79 ref (typ) .031 5.08 ref (typ) .200 "c" ref section "b"-"b" mps-xx-xx.xx-v sub-c-214-xx.xx-xx-x c c fig. 1 mps-06-7.70-01-x-v shown * = not tooled ** = not released for production j sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: vertical mini-power socket by: mps-xx-x.xx-xx-x-v-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 2/15/2007 2 1 sheet scale: 1.5:1 insulator: lcp, color: black contact: copper alloy f:\dwg\misc\mktg\mps-xx-x.xx-xx-x-v-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: 0.038[.0015] max. 3. minimum pushout force: 4.45n[1.0 lb]. 4. parts to be packaged in trays. 5. bow allowed at 0.002 mm/mm [.002 in/in]. 6. minimum -lc pull out force: 2.23 n [0.5 lb] 7. parts to be packaged in trays. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision j
1.42 ref (typ) .056 1.42 - 0.13 +0.20 .056 - .005 +.008 (2 plcs) (no of pos x 5.00[.197]) + 2.64[.104] 2 max sway (typ) lc-07-tm c l c c mps-xx-xx.xx-v-lc 0.25 ref (typ) .010 2.16 ref .085 "d" "d" 0.25 ref .010 2.70 .106 1.00 ref .039 section "d"-"d" c-302-xx.xx-xx-x c-214-xx.xx-xx-x fig. 2 mps-06-7.70-01-x-v-lc shown (same as fig. 1, unless otherwise stated) fig. 3 mps-06-7.70-01-x-v-lc-hs shown (same as fig. 2, unless otherwise stated) sheet of vertical mini-power socket by: mps-xx-x.xx-xx-x-v-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 2/15/2007 2 2 sheet scale: 2:1 revision j f:\dwg\misc\mktg\mps-xx-x.xx-xx-x-v-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
